how to install ubuntu on a mac using netboot

How to install ubuntu on a mac using netboot how to#
How to install ubuntu on a mac using netboot zip file#
How to install ubuntu on a mac using netboot zip#
How to install ubuntu on a mac using netboot free#

**FINAL WARNING** Make sure that the device used in the dd command above is correct. **WARNING** All data on the USB key will be lost is the file path for the input image file. dev/disk2) not a partition designation (ie. is the device the USB key is assigned to.

In the example above the device name is /dev/disk2Īs the root user, use the 'dd' command to write the image to the USB drive. In the example above the device name is /dev/sdb Unmount all volumes on the USB drive by typing the following command: dev/sdb Lexar JumpDrive 15G disk AASNGKKA04EW2GXD dev/sda VMware, VMware_Virtual_S 80G disk Lsblk -p -o NAME,VENDOR,MODEL,SIZE,TYPE,SERIAL Double-check to make sure you have the correct drive. **WARNING** The contents will be overwritten in the next steps.ĭetermine which device the USB drive is assigned as by opening the Terminal and typing the following command. Insert a USB flash drive into a USB slot.

How to install ubuntu on a mac using netboot free#

For the free edition of MemTest86, this file is called, memtest86-usb.img

How to install ubuntu on a mac using netboot zip#

Inside the Zip there is a 'disk image' file.

How to install ubuntu on a mac using netboot zip file#

Download the current Memtest86 package as a Zip file from this page.

Subnet 192.168.1.0 netmask a MemTest86 bootable USB Flash drive in Linux/Mac This entry will set up dynamic addresses: You’ll need to insert lines to the file to configure assigned addresses. Without this line, the client will hang on trying to load the pxe config file. Make sure to include this line at the top: Then configure DHCP service on your server with: You’ll want to put your server’s IP address in and your desired location of the workstation’s OS.įirst, deactivate any DHCP service on your router or other server. (You’ll need to name the files like this or by IP address in hex if you’re setting up more than one diskless workstation.) Here’s an example:ĪPPEND root=/dev/nfs initrd= nfsroot=192.168.1.4:/mnt/hda5/yuki ip=dhcp rw If you know the workstation’s MAC address, name the file 01-aa-bb-cc-dd-ee-ff where aabbccddeeff is the MAC address. After creating this image, you may change the BOOT line back to local.Ĭreate a PXE config file /tftpboot/pxelinux.cfg/default. When editing nf, you want to change the BOOT line from « BOOT=local » to « BOOT=nfs ».

Tftp dgram udp wait nobody /usr/sbin/tcpd /usr/sbin/in.tft pd /tftpbootĬp nf Make sure the line starting with « tftp » ends with « /tftpboot ». Replace vmlinuz-2.6.16-1-486 with the kernel you’re using.Ĭonfigure the tftp service to provide access to /tftpboot by editing /etc/nf. I installed them in the process of trying to get stuff to work.Ĭreate the /tftpboot and start populating it with something like:Ĭp /usr/lib/syslinux/pxelinux.0 /tftpboot/ I’m not sure if pxe and atftpd need to be installed they weren’t in the Ubuntu How-To this is based on. Install the following packages on the server: You’ll want to change these numbers for your own server and router. This how-to assumes the client and server are already set up with Debian Etch, with the client set up on a single root partition.

How to install ubuntu on a mac using netboot how to#

In any case, this is how I figured out how to do it. When I tried using the above how-to with Debian Etch, there were a number of things which didn’t work, and there were a number of things which weren’t explained. This how-to is based on the following Ubuntu how-to: How-To to make a diskless Debian Etch workstation